Adapter #0 ============================================================================== Versions ================ Product Name : PERC 6/i Integrated Serial No : 1122334455667788 FW Package Build: 6.0.2-0002 Mfg. Data ================ Mfg. Date : 06/08/07 Rework Date : 06/08/07 Revision No : Battery FRU : N/A Image Versions in Flash: ================ FW Version : 1.11.52-0396 BIOS Version : NT13-2 WebBIOS Version : 1.1-32-e_11-Rel Ctrl-R Version : 1.01-010B Boot Block Version : 1.00.00.01-0008 Pending Images in Flash ================ None PCI Info ================ Vendor Id : 1000 Device Id : 0060 SubVendorId : 1028 SubDeviceId : 1f0c Host Interface : PCIE Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 5000c50003be5b11 1 5000c50003bdbe01 2 1221000002000000 3 1221000003000000 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 5001e4f036a68e00 BBU : Present Alarm : Absent NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 256MB TPM : Absent Settings ================ Current Time : 8:36:27 1/20, 2011 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% Resynch Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : 128MB Cluster Mode : Disabled Alarm : Disabled Auto Rebuild : Enabled Battery Warning : Enabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Disabled Maintain PD Fail History : Disabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Any Offline VD Cache Preserved : No Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID10, RAID50, RAID60, SRL 3 supported Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 80 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Min Stripe Size : 8 KB Max Stripe Size : 1.0 MB Device Present ================ Virtual Drives : 2 Degraded : 0 Offline : 0 Physical Devices : 5 Disks : 4 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : Yes Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : No Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Disable Copyback : No Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : No Enable SSD Patrol Read : No Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Stripe Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : None Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : No Coercion Mode : 128MB ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : No Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : No Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 1 Disable Ctrl-R : No Enable Web BIOS : No Direct PD Mapping : Yes BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : No Maintain PD Fail History : No Disable Puncturing : No Zero Based Enclosure Enumeration : Yes PreBoot CLI Enabled : No LED Show Drive Activity : No Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 Exit Code: 0x00